View SNP-88612500301_3785034.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number ncd-69b6-05 snp-8 series single-mode pre-angle fc connector plug - for angled-pc / easy-assemble type - technical specifications seiko instruments inc. ofc division. 8, nakase 1-chome mihama-ku, chiba-shi, chiba-ken 261-8507 japan telephone : +81-43-211-1211 facsimile : +81-43-211-8039
ii snp-8 series single-mode pre-angle fc connector plug - for angled-pc / easy-assemble type - technical specifications document number ncd-69b6-05 ncd-69b6-01 september 1996 ncd-69b6-02 may 1998 ncd-69b6-03 july 1999 ncd-69b6-04 april 2000 ncd-69b6-05 may 2003 copyright 1996, 1998,1999, 2000, 2003 by seiko instruments inc. all right reserved. the information contained herein shall not reproduced or disclosed to any third party without the express wr itten consent of sii . the specifications contained herein are subject to change without notice. sii is a trademark of seiko instruments inc. please address any questions, comments, and suggestions to: seiko instruments usa inc. electronics components division 2990 west lomita boulevard torrance, ca 90505, u.s.a. phone: +1-310-517-7780 facsimile: +1-310-517-7792 seiko instruments gmbh ofc division siemensstra?e 9b d-63263 neu-isenburg, germany phone: +49-6102-297-0 facsimile: +49-6102-297-211 seiko instruments (h.k.) ltd. sales department 4th & 5th floor, wyler center 2 200 tai lin pai road, kwai chung n.t., kowloon, hong kong phone: +852-2421-8611 facsimile: +852-2480-5479 seiko instruments taiwan inc. sales department 4f, no.40, sec. 2, min chuan e. rd., taipei 104, taiwan, r.o.c. phone: +886-2-2563-5001 facsimile: +886-2-2521-9519 seiko instruments singapore pte. ltd. component sales department 2, marsiling lane, singapore, 739144, singapore phone: +65-269-1370 facsimile: +65-269-9729
iii table of contents section page 1. provision 1 1.1. application limit 1 2. parts number 1 3. general specifications 2 3.1. parts and materials 2 3.2. physical dimensions 2 3.3. general tolerances 2 4. packing 3 5. note 3 table table 1 parts number 1 table 2 parts and materials 2 table 3 parts and materials (mainbody) 2 table 4 general tolerance 2 figure figure 1 to 2 snp-8 connector 3 to 4 figure 3 to 4 mainbody 5 figure 5 to 12 parts dimensions 6 to 7
iv
1 1 provision 1.1 application limit these specifications apply to the snp- 8 single-mode pre-angle fc connector plug supplied by sii. 2 parts number parts number of the connector is shown in table 1. table 1 parts number model number type number snp-8 831251b302 hood color 0 without hood 8 green 0 1 j 1 hood inner dia package 0 w ith ou t h oo d ,cr i mp i ng-r i ng 3bu lk 1 0 . 9 mm ( non fl ama bl e ) 3 3.0mm (plastic) 6 2.0mm (plastic) cap 9 0.9mm (plastic) 0 without 8 green pvc ferrule inner dia b green ferrule cap s5 to s6 ( 0 . 125 t o 0 . 126 mm ) mar ki ng o f hoo d a pp li ca bl e h oo d ( mm ) 0 w i t h out 0 . 9 mm ( non fl ama bl e ) 1 sii m ar ki ng 0 . 9 t o 3 . 0 mm (pl as ti c ) ( requied ) n type r type compatible
2 3 general specifications 3.1 parts and materials parts and materials are shown in table 2 to 3. table 2 parts and materials no. part name qty material notes 1-1 mainbody 1 see table 3 n-type, (#5,6,7-1,8,9,10 sub-assembled) 1-2 see table 3 r-type compatible, (#5,6,7-2,8,9,10 sub-assembled) 2-1 aluminum alloy for ?3.0 mm cord 2-2 crimping ring (1) aluminum alloy for ?2.0 mm cord 3-1 thermal plastic elastomer ?3.0mm, ul94v-0, green 3-2 thermal plastic elastomer ?2.0mm, ul94v-0, green 3-3 thermal plastic elastomer ?0.9mm, ul94v-0, green 3-4 hood (1) synthetic rubber ?0.9mm, ul94v-0, green 4-1 pp green 4-2 cap (1) pvc green table 3 parts and materials (mainbody) no. part name qty material notes 5 ferrule 1 zirconia - 6 flange 1 brass nickel plating 7-1 nickel plating, n-type 7-2 frame 1 zinc die-casting nickel plating, r-type compatible 8 spring 1 stainless steel - 9 coupling nut 1 brass nickel plating 10 stopper 1 brass nickel plating 3.2 physical dimensions figure 1 to 2 shows the assembled state of snp-8 figure 3 to 4 shows the mainbody. figure 5 to 11 show the parts dimensions. - in accordance with iec 61754-13 fibre optic connector interface - part 13 : type fc-pc connector family. 3.3 general tolerance permissible deviation in dimensions without tole rance indication is in accordance with jis b 0405 class m, as shown in table 4. table 4 general tolerance (jis b 0405 class m) basic size step [mm] over under permissible deviation [mm] 0.5 3 0.1 36 0.1 630 0.2 30 120 0.3
3 4 packing the product is packed to prevent damage during shipment. 5. note when discarding this product, please follow the regulation of your own country.
4 note 1: this drawing shows the tentatively assembled condition. in practice, the connector plug is not assembled like this. note 2: this drawing does not include the caps. unit: mm figure 1 snp-8 connector ( n type)
5 note 1: this drawing shows the tentatively assembled condition. in practice, the connector plug is not assembled like this. note 2: this drawing does not include the caps. unit: mm figure 2 snp-8 connector ( r type compatible )
6 unit: mm figure 3 #1-1 mainbody ( n type ) unit: mm figure 4 #1-2 mainbody ( r type compatible )
7 unit: mm figure 5 #2-1 crimping ring ( for ?3.0 mm cord ) unit: mm figure 6 #2-2 crimping ring ( for ?2.0 mm cord ) unit: mm figure 7 #3-1 hood ( for ?3.0 mm cord ) unit: mm figure 8 #3-2 hood ( for ?2.0 mm cord )
8 unit: mm figure 9 #3-3 hood ( for ?0.9 mm buffered fiber ) unit: mm figure 10 #3-4 hood ( for ?0.9 mm buffered fiber ) unit: mm figure 11 #4-1 cap ( ferrule cap ) unit: mm figure 12 #14-2 cap ( pvc )

▲Up To Search▲

Price & Availability of SNP-88612500301

	To Download SNP-88612500301 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .